Improving Lifestyle with Technology and EVs

Technology has brought so much into our lives that almost everything becomes automated and significantly improves productivity. No doubt, it elevated our lifestyle. As a matter of fact, if you are looking for hacks that can better improve your living, Lifestyle Write for us has a bunch of tips and hacks that can change how you see things.

Technology, People’s Lifestyle and the Birth of Electric Vehicles

While we already established the fact that technology has improved our lives in so many aspects, one of them is in the automotive industry. It’s in the form of electric vehicles that not only made traveling more efficient but also, make the world a greener place. While electric vehicles or EVs are still new in the market, there are many positive impacts it has brought.

EVs are Good for the Environment

There are lots of car buyers and enthusiasts who are convinced to switching to EVs because they’re better for our environment. Since these cars are fully electric, there’s no need for an exhaust system and thus, creates zero emissions.

Without pumping fumes in the air like their gas engine counterparts, EVs are capable of achieving cleaner air with fewer greenhouse gases.

EVs are Renewable

The beauty of electric cars is that they can be powered with renewable resources such as:

  • Water
  • Wind and;
  • Solar

Unlike gasoline though, it’s produced using oil, which is a natural resource. Sadly, it isn’t renewable. As for those who would like to harness the power of renewable energy, then installing solar panels can be extremely useful in powering up your EV.

Besides, electricity is a lot cheaper compared to gas. Electric vehicles usually cost only a third of gas-powered engines. There are numerous cars that are using regenerative braking to be able to add energy to the vehicle which is totally cost-free.

Less Maintenance and more Economical

Without the presence of a gas engine, there is no need to do change the oil in electric cars. That is one thing to cross off on car maintenance. Besides, electric cars are a lot easier on brakes that results in fewer replacements of brake pads and shoes.

Resin-Bonded Joint Filler Technology

Resin-bonded joint fillers are usually used when designing privately used paved areas such as sidewalks in the garden, house entrances, or driveways to the garage. These also have the advantage that they are usually drainable. If you choose a plaster with a joint width that is not too narrow and fill the joints with these joint fillers, the surface remains permeable. It is therefore considered to be “not sealed” – an aspect that should not be neglected with regard to possible wastewater charges.

Resin-bound technology for unbound substructure

In contrast to hydraulic joint fillers, resin-bound systems from can also be used on an unbound substructure, as they are less rigid. They are able to absorb the spring effect of the plaster without damage when stressed or deformed due to temperature fluctuations. A prerequisite, however, is sufficient joint width and depth. As a rule, the joint should be filled to about 2/3 of the stone thickness with a joint filler.

However, if you plan a garage entrance with a slope situation, it makes sense to put the paving stones in an 8-10 cm thick, drainable mortar layer only then to grout. This gives the overall structure better stability and prevents the slight formation of lanes that can be observed again and again when entering a garage.

One or two-component systems for resin-bound driveways

In the case of resin-bound systems, a distinction is made between one-component and two-component systems. resin bound drivewayThese differ on the one hand through different processing methods and on the other hand through their ultimate strength. The two-component systems cure with higher final strength and can therefore also be used with higher traffic loads. In the pedestrian area, on the other hand, you can also grout with one-component products without any problems.

If the one-component system is chosen, it must be ensured that the paving surface must be clean and absolutely dry before it is applied. This also applies to the drying process after it has been introduced – rain protection may have to be used.

For a two-component system or technology, resin-bound joint fillers must be mixed with a hardener component before being applied. The paved surfaces are well pre-wetted, which further simplifies the application of the grout. The grout literally slides through the film of water into the open joints.